Ground Heating Does Not Heat Problem and Solution
Before the natural gas heating spread, people would light stoves in their homes. Every winter, the wood would be cut, the coals would be taken and the stove would be installed. On cold winter days, it would warm up next to those stoves, and the food would cook on the stove from time to time. Besides all her beauty, she had some challenges. It was always needed to carry fuel, clean his ashes and, if he had sooted, cleared the pipes and chimneys. If they didn’t, things could have cost people their lives. We mentioned some details in our article in order not to encounter problems such as underfloor heating.
People got out of all this trouble with the developing technology. With the use of natural gas, heating systems were installed in the houses. Underfloor heating systems are the latest point of developing technologies. Some problems can occur in this system, which is laid on the floor of the apartments and heats the whole area in a cost-saving way. One of the most frequently asked questions is not heating from the floor. We have compiled the problems and solutions that do not heat underfloor heating for you.
Usefulness of the Ground Heating System
Due to the low use of the underfloor heating system, those who are thinking of getting it done are often hesitant. Questions such as whether the system is very costly to install, what do we do if we have any problems or problems after having it done, whether it is fuel efficient or not.
As a result of these questions, they are abandoned when they do not have the right information. Of course, people are right in their hesitation because they don’t know and can’t get the right information. When it comes to cost, what we need to talk about is that it’s very diverse. Because the costs of pipes, collectors and other materials used in systems vary according to the product. However, one thing to remember is that the expense should never be avoided when installing this system. Because the system is in such a state that if there is a poor quality system failure, the whole floor must be broken.
If done with quality and good workmanship, the risk of failure is almost zero. If the installation is well laid, you can make sure that everything is tested by consuming little fuel. This is the initial solution to the problem of underfloor heating in the first place.
Quality workmanship, quality material, professional system are factors that increase the cost. If you want the underfloor heating system to be good, it will not cost you cheaply. However, there will not be much cost difference between it and the heating system you will use. There is no exact price as underfloor heating prices will vary depending on the structure, size and type of underfloor heating of the house. You can contact Isıtmax for underfloor heating prices and benefit from the information of the expert team. We have presented for you the first solution to the problem of underfloor heating. To have a quality system would be to take precautions for this problem from the beginning.
How to Detect Problems with Ground Heating?
Each system has its advantages as well as its disadvantages. Besides the endless advantages of underfloor heating systems, there may be points that are not disadvantages but can cause you problems. First of all, what we need to talk about is, how to detect underfloor heating problems? First of all, the devices used look at what is wrong with the problem. Usually the problems of such systems occur in the boiler or combi boiler that feeds the system. It comes with a complaint of dehydration of the boiler or boiler, i.e. a decrease in the pressure value. This is called underfloor heating leakage. In addition, the problem of underfloor heating is reported as a complaint.
How do we detect water leakage in the system?
First of all, it is necessary to talk about the problem of water leakage. It is necessary to determine if there is a water leakage. The surest way to understand this is to look at the boiler or boiler values. The boiler or boiler has a manometer that shows the pressure value. By tracking the pressure value on the manometer, it can be understood if it is leakage. The water pressure is usually 2. If the pressure value drops to less than 2 and there is no leakage in the visible parts of the connecting places, there is probably a leak in the installation.
After detecting a leak in the sub-ground part of the system, it’s time to locate the leak. Leak detection is done with water leakage search devices. The operating systems of the devices find the leak according to the sound at the exit point of the leak. However, in underfloor heating systems, water leaks are small.
Therefore, they may not be able to hear small leaks. Water or compressed air is pressed into the system to increase the noise of the leak. If the sound from the point where water or compressed air leaks reaches the level that the device can hear, the leakage point is detected by scanning with the device. However, the pipes laid for underfloor heating systems may not withstand too much pressure. Therefore, it may explode during the applied pressure. If not enough compressed air or water is supplied, the exit point of the leak may not be detected. After all this narration, I can hear you saying how to solve the problem of underfloor heating.
Can Water Leakage Be Solved with Chemical Drugs?
An alternative answer to the question of how to detect problems in underfloor heating systems is that it can be solved without needing to be detected. It can be repaired without causing any damage to the floor with a single session. I’m guessing what you think it’s like. Thanks to the chemical drug used for leak repair and repair, all leaks in the installation are repaired on their own. This is how the applied chemical drug solves the depressurized loss in your installation. It repairs all your problems without breaking them and having to locate them. In this way, you can solve your problem of underfloor heating.
Ground Heating System Hard Water Problem
The hardness of water is an important factor for the underfloor heating system. There is a high concentration of ions in the structure of hard water. Due to this situation, it requires a high boiling point and causes more energy expenditure. Calcification occurs on surfaces where water will be heated and continuously increases energy consumption. As a result, calcifications increase inside the pipes, which means more energy consumption.
In other words, the hardness of the water loses its resolution over time and when it is heated and sticks to the surfaces. In addition to energy consumption, the operation of the system in this way can cause the problem of underfloor heating. The solution to this problem is to have the underfloor heating system cleaned regularly.
What is Ground Heating Installation Cleaning?
In underfloor heating systems, installation cleaning, sludge in the system collected inside the pipes, rust lime, etc. to dispose of wastes individually by washing the whole system with pressurized water and chemicals. At the end of this process, all the problems related to heating installation are solved and at the end of the work, the air filled into the pipes is taken and it works more efficiently. Heating pipes from the floor, it travels through the entire circle and eventually returns to the point where it exits, that is, the distributor collector. The so-called collector is a part consisting of red blue hoses and valves, which are usually located under the boiler and where many valves enter and exit. This part allows hot water from the boiler or boiler to be dispersed into the lines, and the other collector on the turn travels around the circle, sending the cooled water back to the boiler to warm up.
The collector, which is a kind of transfer center, also allows to extle the air. The air formed in floor heating comes from the pipes and remains in the collector. In case the collector is cold, the air problem should be suspected first. You can provide air output by turning the perforated air-throwing plugs called purgeors on it. It’s the same. taking the air out of honeycombsor similar. The air is completely exhausted and continued until the water arrives, when the water arrives, the purgeors are tightened and closed. If the water starts flowing before the air comes, it will leak for about 5-10 seconds and if there is still no air, it will be turned off. As a result, we’ll see that there’s no air in the system. Another solution to the problem of underfloor heating is to take air in this way.
You can reach our previous article from https://www.isitmax.com/petekli-evi-yerden-isitmaya-cevirme/ link.
